Ford Small-Block Engine Parts Interchange

Author: George Reid
Publisher: CarTech Inc
ISBN: 1613252129
Category : Transportation
Languages : en
Pages : 146

Book Description
If there is one thing Ford enthusiasts have learned over the years, deciphering which Ford parts work with which Ford engines is a far more difficult task than with many other engine families. Will Cleveland heads fit on my Windsor block? Can I build a stroker motor with factory parts? Can I gain compression by using older-model cylinder heads, and will it restrict flow? Is there a difference between Windsor 2-barrel and 4-barrel heads? These are just a few examples of common questions Ford fans have. These and many other questions are examined in this all-new update of a perennial best seller. Thoroughly researched and, unlike previous editions, now focused entirely on the small-block Windsor and Cleveland engine families, Ford Small Block Engine Parts Interchange includes critical information on Ford’s greatest small-block engines and goes into great detail on the highly desirable high-performance hardware produced throughout the 1960s, 1970s, and 1980s. By combining some of the best parts from various years, some great performance potential can be unlocked in ways Ford never offered to the general public. Following the advice in Ford Small-Block Engine Parts Interchange, these engine combinations can become reality. You will find valuable information on cranks, blocks, heads, cams, intakes, rods, pistons, and even accessories to guide you through your project. Author George Reid has once again done extensive research to accurately deliver a thorough and complete collection of Ford small-block information in this newly revised edition. Knowing what internal factory engine parts can be used across the wide range of production Ford power plants is invaluable to the hot rodder and swap meet/eBay shopper. Whether building a stroker Cleveland or a hopped-up Windsor, this book is an essential guide.

Ford Big-Block Parts Interchange

Author: George Reid
Publisher: CarTech Inc
ISBN: 1613253443
Category : Transportation
Languages : en
Pages : 145

Book Description
Over the course of performance car history, and specifically muscle car history, big-block engines are particularly beloved, and for good reason. Not only are they the essence of what a muscle car is, but before modern technology and stroker engines, they were also the best way to make a lot of horsepower. All of the Detroit manufacturers had their versions of big-block engines, and Ford was no exception. Actually, Ford was somewhat unique in that it had two very different big-block engine designs during the muscle car era. The FE engine was a design pioneered in the late 1950s, primarily as a more powerful replacement for the dated Y-block design because cars were becoming bigger and heavier, and therefore, necessitated more power to move. What started as torquey engines meant to move heavyweight sedans morphed into screaming high-performance mills that won Le Mans and drag racing championships through the 1960s. By the late 1960s, the design was dated, so Ford replaced the FE design with the "385" series, also known as the "Lima" design, which was more similar to the canted-valve Cleveland design being pioneered at the same time. It didn't share the 1960s pedigree of racing success, but the new design was better in almost every way; it exists via Ford motorsports offerings to this day. In Ford Big-Block Parts Interchange, Ford expert and historian George Reid covers both engines completely. Interchange and availability for all engine components are covered including cranks, rods, pistons, camshafts, engine blocks, intake and exhaust manifolds, carburetors, distributors, and more. Expanding from the previous edition of High-Performance Ford Parts Interchange that covered both small- and big-block engines in one volume, this book cuts out the small-block information and devotes every page to the FE Series and 385 big-blocks from Ford, which allows for more complete and extensive coverage. p.p1 {margin: 0.0px 0.0px 0.0px 0.0px; font: 12.0px Arial}

High-performance Ford Engine Parts Interchange

Author: George Reid
Publisher: S-A Design
ISBN: 9781934709191
Category : Transportation
Languages : en
Pages : 160

Book Description
Includes critical information on Ford's greatest V-8 engines with great detail on the high-performance hardware produced throughout the '60s ,'70s and '80s, as well as information on cranks, blocks, heads, cams, intakes, rods, pistons, and more.

How to Build Big-Inch Ford Small Blocks

Author: George Reid
Publisher: CarTech Inc
ISBN: 1884089836
Category : Transportation
Languages : en
Pages : 130

Book Description
In this definitive guide, the author explains the concept of building a stroker, paying special attention to the effect that increasing the bore and stroke have on the engine as a whole.

How to Build Max-Performance Ford FE Engines

Author: Barry Rabotnick
Publisher: CarTech Inc
ISBN: 1934709158
Category : Transportation
Languages : en
Pages : 146

Book Description
The Ford FE (Ford Edsel) engine is one of the most popular engines Ford ever produced, and it powered most Ford and Mercury cars and trucks from the late 1950s to the mid-1970s. For many of the later years, FE engines were used primarily in truck applications. However, the FE engine is experiencing a renaissance; it is now popular in high-performance street, strip, muscle cars, and even high-performance trucks. While high-performance build-up principles and techniques are discussed for all engines, author Barry Rabotnick focuses on the max-performance build-up for the most popular engines: the 390 and 428. With the high-performance revival for FE engines, a variety of builds are being performed from stock blocks with mild head and cam work to complete aftermarket engines with aluminum blocks, high-flow heads, and aggressive roller cams. How to Build Max-Performance Ford FE Engines shows you how to select the ideal pistons, connecting rods, and crankshafts to achieve horsepower requirements for all applications. The chapter on blocks discusses the strengths and weaknesses of each particular block considered. The book also examines head, valvetrain, and cam options that are best suited for individual performance goals. Also covered are the best-flowing heads, rocker-arm options, lifters, and pushrods. In addition, this volume covers port sizing, cam lift, and the best rocker-arm geometry. The FE engines are an excellent platform for stroking, and this book provides an insightful, easy-to-follow approach for selecting the right crank, connecting rods, pistons, and making the necessary block modifications. This is the book that Ford FE fans have been looking for.

Ford 429/460 Engines

Author: Charles Morris
Publisher: CarTech Inc
ISBN: 161325492X
Category : Transportation
Languages : en
Pages : 145

Book Description
Ford was unique in that it had two very different big-block engine designs during the height of the muscle car era. The original FE engine design was pioneered in the late 1950s, primarily as a more powerful replacement for the dated Y-block design. What began as torquey engines meant to move heavyweight sedans morphed into screaming high-performance mills that won Le Mans and drag racing championships throughout the 1960s. By the late 1960s, the FE design was dated, so Ford replaced it with the 385 series, also known as the Lima design, in displacements of 429 and 460 ci, which was similar to the canted-valve Cleveland design being pioneered at the same time. It didn’t share the FE pedigree of racing success, mostly due to timing, but the new design was better in almost every way; it exists via Ford Motorsports’ offerings to this day. Beginning in 1971, the 429 found its way between the fenders of Mustangs and Torinos in high-compression 4-barrel versions called the Cobra Jet and Super Cobra Jet, and they were some of the most powerful passenger car engines Ford had ever built. If the muscle car era had not died out shortly after the release of these powerful engines, without a doubt the 429 performance variants would be ranked with the legendary big-blocks of all time. In this revised edition of How to Rebuild Big-Block Ford Engines, now titled Ford 429/460 Engines: How to Rebuild, Ford expert Charles Morris covers all the procedures, processes, and techniques for rebuilding your 385 Series big-block. Step-by-step text provides details for determining whether your engine actually needs a rebuild, preparation and removal, disassembly, inspection, cleaning, machining and parts selection, reassembly, start-up, and tuning. Also included is a chapter in building the special Boss 429 engines, as well as a bonus chapter on the Ford 351 Cleveland, Ford’s little brother to the big-block.

How to Rebuild Small-Block Ford Engines

Author: Tom Monroe
Publisher: Penguin
ISBN: 9780912656892
Category : Transportation
Languages : en
Pages : 170

Book Description
If you have a small-block Ford, then you need this book! This detailed guide covers the step-by-step rebuilding process of the popular small-block Ford engine. Parts inspection, diagnosis, reconditioning, and assembly are outlined in simple text. Hundreds of photos, charts, and diagrams visually walk you through the entire rebuild. You’ll be able to completely disassemble your engine, recondition the block and cylinder heads, then reassemble and install the engine in your vehicle. There’s even a section on how to perform tune-ups to maximize performance and economy. Sections on parts interchanging will help you identify all parts and determine which ones can and can’t be swapped. This is truly a “hands-on” book. Don’t put off your project any longer. Start rebuilding your small-block Ford today!

Ford FE Engines

Author: Barry Rabotnick
Publisher: CarTech Inc
ISBN: 1613252447
Category : Transportation
Languages : en
Pages : 145

Book Description
Ford FE engines, which were manufactured from the late 1950s all the way through the mid-1970s, were designated as the large-displacement engines in the Ford lineup. FE means Ford Edsel, and reflects an era when Ford sought to promote the Edsel name. The design of these engines was implemented to increase displacement over its predecessor, the Y-Block engines of the previous decade. Early models were fairly modest in displacement, as were most big-blocks of the era, but they grew quickly to fill the needs of rapidly changing chassis requirements and consumer demand for larger vehicles. As it grew, the FE engine performed admirably as a heavy passenger car and light truck engine. It also became quite accomplished in performance circles, winning the 24 Hours of Le Mans, as well as powering Ford’s muscle car and drag racing programs in the mid- to late 1960s. In this book, you will learn everything you need to know to rebuild one of these legendary engines. CarTech's unique Workbench series format takes you step-by-step through the entire rebuilding process. Covered are engine identification and selection, disassembly, cleaning, parts analysis and assessment, machine shop processes, replacement parts selection, re-assembly and start-up/break-in techniques. Along the way you find helpful tips on performance upgrades, trouble spots to look for, special tools required, and professional builder's tips. FE master, owner of Survival Motorsports, and veteran author Barry Rabotnick shares all of his tricks and secrets on building a durable and reliable FE engine. Whether you are simply rebuilding an old truck for reliable service use, restoring a 100-point show car, or building the foundation for a high-performance street and strip machine, this book will be an irreplaceable resource for all your future FE engine projects.

How to Rebuild the Big-Block Chevrolet

Author: Tony Huntimer
Publisher: CarTech Inc
ISBN: 1932494537
Category : Transportation
Languages : en
Pages : 162

Book Description
In our popular Workbench Series, How to Rebuild the Big Block Chevrolet covers the basics of any engine rebuild in over 450 color photos of step-by-step instruction. Subjects covered include the history of the big block Chevy, preperation and tool requirements, engine removal and teardown, first inspection, parts, machine work and clean-up, final engine assembly, and start-up. This book is essential for not only enthusiasts looking to rebuild their big-block Chevy, but as a guideline for building performance applications as well.

How to Rebuild Ford V-8 Engines

Author: Tom Monroe
Publisher: Penguin
ISBN: 9780895860361
Category : Transportation
Languages : en
Pages : 164

Book Description
If you have one of the 351C, 351M, 400, 429 or 460 Ford V8s, this comprehensive book is a must. It walks you through a complete engine rebuild, step-by-step, with minimum use of special tools. Save money by finding out if your engine really needs rebuilding, or just simple and inexpensive maintenance. Results from diagnosis outlines in this book should be your guide, not the odometer. All rebuilding steps are illustrated from beginning to end. How to inspect parts of damage and wear, and to recondition each part yourself to get the job done right! The most complete source of information identifying major engine parts. Casting numbers, parts description, when a part was used and how it can be interchanged is fully covered in the text, in 20 tables and in 560 photos or drawings. This book will make you an expert!