Author: Mandy Concepcion
Publisher: Mandy Concepcion
ISBN:
Category : Transportation
Languages : en
Pages : 59
Book Description
Automotive Scan Tool PID Diagnostics (Diagnostics Strategies of Modern Automotive Systems ) By Mandy Concepcion In this section, the different techniques of scan tool parameter (PID) analysis will be exposed. Techniques involving PID analysis are quickly catching on, due to their speed and accuracy. By properly analyzing the different scanner PIDs, the technician can arrive at the source of the problem much faster and accurately. These procedures give rise to the new term “driver seat diagnostics”, since most of the preliminary diagnostic work is done through the scanner. However, these techniques will in no way replace the final manual tests that are a part of every diagnostic path. They are simply geared to point the technician in the right direction. Table of Contents INTRODUCTION (Introduction to scan tool diagnostics and the relevance of using PIDs or scanner parameter to perform the first leg of all diagnostics.) - Theory of Operation Behind the Different PIDs (Describes CARB, the difference between generic and enhanced PIDs, the FTP) - OBD II Generic PIDs (PID calculated and actual values, calculated data relationships, base injection timing, ECM value substitution) - OBD I & II General PID analysis (erasing code-or not, recording, analyzing and pinpoint tests, separating PIDs into groups) - Fuel Delivery Fault Detection (fuel delivery issues, intake air temp. sensor, BARO sensor, Engine LOAD, RPM PID, Short-Term Fuel Trims, Long-Term Fuel Trims, 60% of check engine light issues, block learn/integrators, Example 1: injector fault, Example 2: intake gasket issues, fuel status, ignition timing, MAP/MAF, TPS, O2 sensor, IAC, Closed Throttle, injector pulse width, voltage power, injector dutycycle, fuel trim cell) - Test #1 (Determining an engine’s fuel Consumption (rich-lean operation, duty-cycle to fuel trim relationship, O2 sensor to fuel trim relation, FT and vacuum leaks, ignition timing and idle control, test conclusion) - Test # 2 (Misfire Detection Strategy, EGR, Ignition and Mechanical misfires) (misfires and OBD2, scanner misfire detection – a time saver, OBD2 40 and 80 cycle misfire, ignition, injector and EGR density misfire, coil-on-plug, misfires and O2 sensor, lean O2 & Secondary misfire, O2 sensor & injector misfires, leaky injector, EGR and the MAP, Type A, B, C misfires, test conclusion) - Test # 3 (Air/Fuel Ratio Faults) (air-fuel imbalance, MAF and post O2 sensors, open-closed-loop, fuel enable, HC & CO relation to AF issues, test conclusion) - Test # 4 (BARO, MAP & MAF PID analysis) (MAP & valve timing faults, ECM behavior, fuel delivery or duty cycle test, volumetric efficiency, , test conclusion) - Test # 5 (Clogged exhaust) (clogged catalytic converter detection, TPS, MAF and converters, idle and WOT or wide open throttle values, vacuum readings, MAP to WOT chats analysis, engine and MAP vacuum, test conclusion) - Test # 6 (EGR Fault Detection) (EGR and MAP values, ECM reaction to EGR issues, EGR temp sensor, DPFE sensor, EGR and O2-MAP and lift position sensor, EGR and engine pre-loading, EGR and the ECM erroneous high LOAD issues, test conclusion) - Test # 7 (O2 Sensor Heater) (O2 heaters and why?, tough to check O2 heater issues, O2 heater effect on signal output, O2 heater bias voltage, engine off and O2 changing value, test conclusion) - Test # 8 (Resetting Fuel Trims) (resetting injection pulse corrections, long-term and short-term fuel trims, learn condition, Lambda, case study on fuel trims, FT resetting according to manufacturer, test conclusion) - Test # 9 (Engine Cranking Vacuum Test) (MAP/MAF cranking vacuum, vacuum to PID analysis, vacuum leaks, gauge-PID test, sources of leaks, cranking values, test conclusion)
Automotive Diagnostic Systems
Author: Keith McCord
Publisher: CarTech Inc
ISBN: 1934709069
Category : Transportation
Languages : en
Pages : 148
Book Description
"OBD expert, tuner, and author Keith McCord explains system architecture, function, and operation. He shows you how to use a hand-held scanner, connect it to the port connector in the car, and interpret the data. But most importantly, he shows you a practical, analytical, and methodical process for tackling a problem, so you can quickly trace its actual source and fix the root cause and not just the symptom..." -- from page 4 of cover.
Publisher: CarTech Inc
ISBN: 1934709069
Category : Transportation
Languages : en
Pages : 148
Book Description
"OBD expert, tuner, and author Keith McCord explains system architecture, function, and operation. He shows you how to use a hand-held scanner, connect it to the port connector in the car, and interpret the data. But most importantly, he shows you a practical, analytical, and methodical process for tackling a problem, so you can quickly trace its actual source and fix the root cause and not just the symptom..." -- from page 4 of cover.
How To Use Automotive Diagnostic Scanners
Author: Tracy Martin
Publisher: Motorbooks
ISBN: 1627886486
Category : Transportation
Languages : en
Pages : 203
Book Description
From hand-held, dedicated units to software that turns PCs and Palm Pilots into powerful diagnostic scanners, auto enthusiasts today have a variety of methods available to make use of on-board diagnostic systems. And not only can they be used to diagnose operational faults, they can be used as low-budget data acquistion systems and dynamometers, so you can maximize your vehicle's performance. Beginning with why scanners are needed to work effectively on modern cars, this book teaches you how to choose the right scanner for your application, how to use the tool, and what each code means. "How To Use Automotive Diagnostic Scanners" is illustrated with photos and diagrams to help you understand OBD-I and OBD-II systems (including CAN) and the scanners that read the information they record. Also included is a comprehensive list of codes and what they mean. From catalytic converters and O2 sensors to emissions and automotive detective work, this is the complete reference for keeping your vehicle EPA-compliant and on the road!
Publisher: Motorbooks
ISBN: 1627886486
Category : Transportation
Languages : en
Pages : 203
Book Description
From hand-held, dedicated units to software that turns PCs and Palm Pilots into powerful diagnostic scanners, auto enthusiasts today have a variety of methods available to make use of on-board diagnostic systems. And not only can they be used to diagnose operational faults, they can be used as low-budget data acquistion systems and dynamometers, so you can maximize your vehicle's performance. Beginning with why scanners are needed to work effectively on modern cars, this book teaches you how to choose the right scanner for your application, how to use the tool, and what each code means. "How To Use Automotive Diagnostic Scanners" is illustrated with photos and diagrams to help you understand OBD-I and OBD-II systems (including CAN) and the scanners that read the information they record. Also included is a comprehensive list of codes and what they mean. From catalytic converters and O2 sensors to emissions and automotive detective work, this is the complete reference for keeping your vehicle EPA-compliant and on the road!
The Car Hacker's Handbook
Author: Craig Smith
Publisher: No Starch Press
ISBN: 1593277709
Category : Technology & Engineering
Languages : en
Pages : 306
Book Description
Modern cars are more computerized than ever. Infotainment and navigation systems, Wi-Fi, automatic software updates, and other innovations aim to make driving more convenient. But vehicle technologies haven’t kept pace with today’s more hostile security environment, leaving millions vulnerable to attack. The Car Hacker’s Handbook will give you a deeper understanding of the computer systems and embedded software in modern vehicles. It begins by examining vulnerabilities and providing detailed explanations of communications over the CAN bus and between devices and systems. Then, once you have an understanding of a vehicle’s communication network, you’ll learn how to intercept data and perform specific hacks to track vehicles, unlock doors, glitch engines, flood communication, and more. With a focus on low-cost, open source hacking tools such as Metasploit, Wireshark, Kayak, can-utils, and ChipWhisperer, The Car Hacker’s Handbook will show you how to: –Build an accurate threat model for your vehicle –Reverse engineer the CAN bus to fake engine signals –Exploit vulnerabilities in diagnostic and data-logging systems –Hack the ECU and other firmware and embedded systems –Feed exploits through infotainment and vehicle-to-vehicle communication systems –Override factory settings with performance-tuning techniques –Build physical and virtual test benches to try out exploits safely If you’re curious about automotive security and have the urge to hack a two-ton computer, make The Car Hacker’s Handbook your first stop.
Publisher: No Starch Press
ISBN: 1593277709
Category : Technology & Engineering
Languages : en
Pages : 306
Book Description
Modern cars are more computerized than ever. Infotainment and navigation systems, Wi-Fi, automatic software updates, and other innovations aim to make driving more convenient. But vehicle technologies haven’t kept pace with today’s more hostile security environment, leaving millions vulnerable to attack. The Car Hacker’s Handbook will give you a deeper understanding of the computer systems and embedded software in modern vehicles. It begins by examining vulnerabilities and providing detailed explanations of communications over the CAN bus and between devices and systems. Then, once you have an understanding of a vehicle’s communication network, you’ll learn how to intercept data and perform specific hacks to track vehicles, unlock doors, glitch engines, flood communication, and more. With a focus on low-cost, open source hacking tools such as Metasploit, Wireshark, Kayak, can-utils, and ChipWhisperer, The Car Hacker’s Handbook will show you how to: –Build an accurate threat model for your vehicle –Reverse engineer the CAN bus to fake engine signals –Exploit vulnerabilities in diagnostic and data-logging systems –Hack the ECU and other firmware and embedded systems –Feed exploits through infotainment and vehicle-to-vehicle communication systems –Override factory settings with performance-tuning techniques –Build physical and virtual test benches to try out exploits safely If you’re curious about automotive security and have the urge to hack a two-ton computer, make The Car Hacker’s Handbook your first stop.
Automotive Mechatronics
Author: Konrad Reif
Publisher: Springer
ISBN: 3658039752
Category : Technology & Engineering
Languages : en
Pages : 549
Book Description
As the complexity of automotive vehicles increases this book presents operational and practical issues of automotive mechatronics. It is a comprehensive introduction to controlled automotive systems and provides detailed information of sensors for travel, angle, engine speed, vehicle speed, acceleration, pressure, temperature, flow, gas concentration etc. The measurement principles of the different sensor groups are explained and examples to show the measurement principles applied in different types.
Publisher: Springer
ISBN: 3658039752
Category : Technology & Engineering
Languages : en
Pages : 549
Book Description
As the complexity of automotive vehicles increases this book presents operational and practical issues of automotive mechatronics. It is a comprehensive introduction to controlled automotive systems and provides detailed information of sensors for travel, angle, engine speed, vehicle speed, acceleration, pressure, temperature, flow, gas concentration etc. The measurement principles of the different sensor groups are explained and examples to show the measurement principles applied in different types.
OBD-II & Electronic Engine Management Systems
Author: Bob Henderson
Publisher: Haynes Manuals N. America, Incorporated
ISBN: 9781563926129
Category : Transportation
Languages : en
Pages : 272
Book Description
This manual takes the mystery out of Second-Generation On-Board Diagnostic Systems allowing you to understand your vehicles OBD-II sytem, plus what to do when the "Check Engine" light comes on, from reading the code to diagnosing and fixing the problem. Includes a comprehensive list of computer codes. Computer-controlled car repair made easy! For all car and light truck models manufactured since 1996. Understand your vehicle's On-Board Diagnostic system How to deal with that "Check Engine" light--from reading the code to diagnosing and fixing the problem Comprehensive computer codes list Diagnostic tools: Powertrain management fundamentals OBD-II "monitors" explained Generic trouble codes that cover all models! Manufacturer-specific trouble codes for GM, Ford, Chrysler, Toyota/Lexus and Honda/Acura vehicles Let your car's computer help you find the problem! Component replacement procedures Glossary and acronym list Fully illustrated with over 250 photographs and drawings
Publisher: Haynes Manuals N. America, Incorporated
ISBN: 9781563926129
Category : Transportation
Languages : en
Pages : 272
Book Description
This manual takes the mystery out of Second-Generation On-Board Diagnostic Systems allowing you to understand your vehicles OBD-II sytem, plus what to do when the "Check Engine" light comes on, from reading the code to diagnosing and fixing the problem. Includes a comprehensive list of computer codes. Computer-controlled car repair made easy! For all car and light truck models manufactured since 1996. Understand your vehicle's On-Board Diagnostic system How to deal with that "Check Engine" light--from reading the code to diagnosing and fixing the problem Comprehensive computer codes list Diagnostic tools: Powertrain management fundamentals OBD-II "monitors" explained Generic trouble codes that cover all models! Manufacturer-specific trouble codes for GM, Ford, Chrysler, Toyota/Lexus and Honda/Acura vehicles Let your car's computer help you find the problem! Component replacement procedures Glossary and acronym list Fully illustrated with over 250 photographs and drawings
Automotive Control Systems
Author: Uwe Kiencke
Publisher: Springer Science & Business Media
ISBN: 3540231390
Category : Technology & Engineering
Languages : en
Pages : 522
Book Description
Written by two of the most respected, experienced and well-known researchers and developers in the field (e.g., Kiencke worked at Bosch where he helped develop anti-breaking system and engine control; Nielsen has lead joint research projects with Scania AB, Mecel AB, Saab Automobile AB, Volvo AB, Fiat GM Powertrain AB, and DaimlerChrysler. Reflecting the trend to optimization through integrative approaches for engine, driveline and vehicle control, this valuable book enables control engineers to understand engine and vehicle models necessary for controller design and also introduces mechanical engineers to vehicle-specific signal processing and automatic control. Emphasis on measurement, comparisons between performance and modelling, and realistic examples derive from the authors’ unique industrial experience . The second edition offers new or expanded topics such as diesel-engine modelling, diagnosis and anti-jerking control, and vehicle modelling and parameter estimation. With only a few exceptions, the approaches
Publisher: Springer Science & Business Media
ISBN: 3540231390
Category : Technology & Engineering
Languages : en
Pages : 522
Book Description
Written by two of the most respected, experienced and well-known researchers and developers in the field (e.g., Kiencke worked at Bosch where he helped develop anti-breaking system and engine control; Nielsen has lead joint research projects with Scania AB, Mecel AB, Saab Automobile AB, Volvo AB, Fiat GM Powertrain AB, and DaimlerChrysler. Reflecting the trend to optimization through integrative approaches for engine, driveline and vehicle control, this valuable book enables control engineers to understand engine and vehicle models necessary for controller design and also introduces mechanical engineers to vehicle-specific signal processing and automatic control. Emphasis on measurement, comparisons between performance and modelling, and realistic examples derive from the authors’ unique industrial experience . The second edition offers new or expanded topics such as diesel-engine modelling, diagnosis and anti-jerking control, and vehicle modelling and parameter estimation. With only a few exceptions, the approaches
Pediatric Emergency Critical Care and Ultrasound
Author: Stephanie J. Doniger
Publisher: Cambridge University Press
ISBN: 1107433622
Category : Medical
Languages : en
Pages : 371
Book Description
Emergency bedside ultrasound assessment is well established for adult patients, but has only recently been introduced into everyday clinical practice for the care of pediatric patients. Pediatric Emergency Critical Care and Ultrasound is a concise, practical text which explains the principles of ultrasound, its diagnostic application in all organ systems and its use as a procedural adjunct. Both well-established and innovative applications are described, assisting the practitioner in incorporating ultrasound into daily practice, facilitating patient care and decreasing radiation exposure. Case studies and abundant illustrations enable the reader to study the appropriate techniques in detail and learn from real examples from the pediatric emergency department and intensive care unit. Pediatric Emergency Critical Care and Ultrasound is the first comprehensive bedside ultrasonography resource focusing on pediatric patients and is essential reading not only for pediatric emergency medicine subspecialists but for all emergency physicians, intensivists/critical care physicians and pediatricians.
Publisher: Cambridge University Press
ISBN: 1107433622
Category : Medical
Languages : en
Pages : 371
Book Description
Emergency bedside ultrasound assessment is well established for adult patients, but has only recently been introduced into everyday clinical practice for the care of pediatric patients. Pediatric Emergency Critical Care and Ultrasound is a concise, practical text which explains the principles of ultrasound, its diagnostic application in all organ systems and its use as a procedural adjunct. Both well-established and innovative applications are described, assisting the practitioner in incorporating ultrasound into daily practice, facilitating patient care and decreasing radiation exposure. Case studies and abundant illustrations enable the reader to study the appropriate techniques in detail and learn from real examples from the pediatric emergency department and intensive care unit. Pediatric Emergency Critical Care and Ultrasound is the first comprehensive bedside ultrasonography resource focusing on pediatric patients and is essential reading not only for pediatric emergency medicine subspecialists but for all emergency physicians, intensivists/critical care physicians and pediatricians.